135038 Arduino Flame Detection Sensor Module - Revision history

Donsez at 15:22, 10 August 2012

2012-08-10T15:22:03Z

← Older revision		Revision as of 15:22, 10 August 2012
Line 1:		Line 1:
			[[Image:FlameSensor1.jpg\|200px\|thumb\|right\|Flame Detection Sensor Module with flame]]
			[[Image:FlameSensor2.jpg\|200px\|thumb\|right\|Flame Detection Sensor Module without flame]]


	[http://www.dealextreme.com/p/135038 Arduino Flame Detection Sensor Module]		[http://www.dealextreme.com/p/135038 Arduino Flame Detection Sensor Module]
	Also : http://www.hobbycomponents.com/index.php?route=product/product&product_id=144		Also : http://www.hobbycomponents.com/index.php?route=product/product&product_id=144

Donsez at 09:32, 10 August 2012

2012-08-10T09:32:14Z

← Older revision		Revision as of 09:32, 10 August 2012
Line 13:		Line 13:

	This is a simple example of how to use the HobbyComponents Arduino flame detection		This is a simple example of how to use the HobbyComponents Arduino flame detection
	module (HCARDU0024). The sensor has two outputs, an ~~analogue~~ output that is		module (HCARDU0024). The sensor has two outputs, an analog output that is
	dependent on how strong a flame is detected, or a digital output that will go high if		dependent on how strong a flame is detected, or a digital output that will go high if
	a flame is detected above a threshold set by the modules potentiometer.		a flame is detected above a threshold set by the modules potentiometer.
Line 22:		Line 22:
	SENSOR PINOUT:		SENSOR PINOUT:

	PIN 1: ~~Analogue~~ out		PIN 1: Analog out
	PIN 2: Ground		PIN 2: Ground
	PIN 3: +5V		PIN 3: +5V

Donsez at 09:30, 10 August 2012

2012-08-10T09:30:17Z

← Older revision		Revision as of 09:30, 10 August 2012
Line 1:		Line 1:
	[http://www.dealextreme.com/p/135038 Arduino Flame Detection Sensor Module]		[http://www.dealextreme.com/p/135038 Arduino Flame Detection Sensor Module]
			Also : http://www.hobbycomponents.com/index.php?route=product/product&product_id=144

	''Sensor for flame wavelengths between 760 nm to 1100 nm infrared is most sensitive; Module has two outputs: 1, AO, analog output, real-time output voltage signal on the thermal resistance; 2, DO, when the temperature reaches a certain threshold, the output high and low signal threshold adjustable via potentiometer; 60 degree detection sensor. Voltage: DC 3~5.5V''		''Sensor for flame wavelengths between 760 nm to 1100 nm infrared is most sensitive; Module has two outputs: 1, AO, analog output, real-time output voltage signal on the thermal resistance; 2, DO, when the temperature reaches a certain threshold, the output high and low signal threshold adjustable via potentiometer; 60 degree detection sensor. Voltage: DC 3~5.5V''


			<pre>
			ARD_Flame_Detector_Sensor_HCARDU0024_Example.pde

			/* FILE: ARD_Flame_Detector_Sensor_HCARDU0024_Example.pde
			DATE: 03/07/12
			VERSION: 0.1

			This is a simple example of how to use the HobbyComponents Arduino flame detection
			module (HCARDU0024). The sensor has two outputs, an analogue output that is
			dependent on how strong a flame is detected, or a digital output that will go high if
			a flame is detected above a threshold set by the modules potentiometer.

			This example program reads the status of both sensor outputs and outputs the result
			to the UART.

			SENSOR PINOUT:

			PIN 1: Analogue out
			PIN 2: Ground
			PIN 3: +5V
			PIN 4: Digital out

			You may copy, alter and reuse this code in any way you like but please leave
			reference to HobbyComponents.com in your comments if you redistribute this code. */


			/* Select the input pin for the flame detectors analogue output. */
			#define FLAME_DETECT_ANA A0

			/* Select the input pin for the flame detectors digital output. */
			#define FLAME_DETC_DIO 2



			/* Initialise serial and DIO */
			void setup()
			{
			/* Setup the serial port for displaying the status of the sensor */
			Serial.begin(9600);

			/* Configure the DIO pin the sensors digital output will be connected to */
			pinMode(FLAME_DETC_DIO, INPUT);
			}


			/* Main program loop */
			void loop()
			{
			/* Read the sensors analogue output and send it to the serial port */
			Serial.print("Sensor Value: ");
			Serial.print(analogRead(FLAME_DETECT_ANA));

			/* Read the status of the sensors digital output and if it is high
			then send an alert to the UART */
			if (digitalRead(FLAME_DETC_DIO))
			{
			Serial.println(" FLAME DETECTED!");
			}else
			{
			Serial.println();
			}

			}
			</pre>

Donsez at 14:35, 9 August 2012

2012-08-09T14:35:36Z

← Older revision		Revision as of 14:35, 9 August 2012
Line 1:		Line 1:
	[http://www.dealextreme.com/p/135038 Arduino Flame Detection Sensor Module]		[http://www.dealextreme.com/p/135038 Arduino Flame Detection Sensor Module]

			''Sensor for flame wavelengths between 760 nm to 1100 nm infrared is most sensitive; Module has two outputs: 1, AO, analog output, real-time output voltage signal on the thermal resistance; 2, DO, when the temperature reaches a certain threshold, the output high and low signal threshold adjustable via potentiometer; 60 degree detection sensor. Voltage: DC 3~5.5V''

Donsez: Created page with "[http://www.dealextreme.com/p/135038 Arduino Flame Detection Sensor Module]"

2012-08-09T14:34:18Z

Created page with "[http://www.dealextreme.com/p/135038 Arduino Flame Detection Sensor Module]"

New page

[http://www.dealextreme.com/p/135038 Arduino Flame Detection Sensor Module]