RobAIR2013-RICM5-Suivi/BurnBootloader - Revision history

Donsez: /* Introduction */

2013-05-10T09:22:35Z

Introduction

← Older revision		Revision as of 09:22, 10 May 2013
Line 5:		Line 5:
	This tutorial explains how to use an Arduino board (Arduino Uno) as an AVR ISP (in-system programmer). This allows you to use the board to burn the bootloader onto an AVR (the ATmega168 used in Arduino). This steps have been tested with Arduino 022 and Windows as OS. (Not the same in results on Linux :( )		This tutorial explains how to use an Arduino board (Arduino Uno) as an AVR ISP (in-system programmer). This allows you to use the board to burn the bootloader onto an AVR (the ATmega168 used in Arduino). This steps have been tested with Arduino 022 and Windows as OS. (Not the same in results on Linux :( )

	Attention: This is not required for normal use of the [[Wild Thumper Controller]] (normally come with a bootloader).		Attention: This is not required for normal use of the [[Dagu Wild Thumper Controller Board]] (normally come with a bootloader).

	This tutorials is based on the tutorials http://arduino.cc/en/Tutorial/ArduinoISP and http://letsmakerobots.com/node/32096. These instructions are based on Arduino 022 running on Windows (not successful results on Linux).		This tutorials is based on the tutorials http://arduino.cc/en/Tutorial/ArduinoISP and http://letsmakerobots.com/node/32096. These instructions are based on Arduino 022 running on Windows (not successful results on Linux).

Donsez: /* Introduction */

2013-05-10T09:17:22Z

Introduction

← Older revision		Revision as of 09:17, 10 May 2013
Line 5:		Line 5:
	This tutorial explains how to use an Arduino board (Arduino Uno) as an AVR ISP (in-system programmer). This allows you to use the board to burn the bootloader onto an AVR (the ATmega168 used in Arduino). This steps have been tested with Arduino 022 and Windows as OS. (Not the same in results on Linux :( )		This tutorial explains how to use an Arduino board (Arduino Uno) as an AVR ISP (in-system programmer). This allows you to use the board to burn the bootloader onto an AVR (the ATmega168 used in Arduino). This steps have been tested with Arduino 022 and Windows as OS. (Not the same in results on Linux :( )

	Attention: This is not required for normal use of the Wild Thumper Controller (normally come with a bootloader).		Attention: This is not required for normal use of the [[Wild Thumper Controller]] (normally come with a bootloader).

	This tutorials is based on the tutorials http://arduino.cc/en/Tutorial/ArduinoISP and http://letsmakerobots.com/node/32096. These instructions are based on Arduino 022 running on Windows (not successful results on Linux).		This tutorials is based on the tutorials http://arduino.cc/en/Tutorial/ArduinoISP and http://letsmakerobots.com/node/32096. These instructions are based on Arduino 022 running on Windows (not successful results on Linux).

ElizabethPaz: /* Instructions */

2013-03-21T09:09:45Z

Instructions

← Older revision		Revision as of 09:09, 21 March 2013
Line 42:		Line 42:

	* If this doesn't work, execute cmd.exe and execute the following command:		* If this doesn't work, execute cmd.exe and execute the following command:
	C:\Users\~~Liz\Desktop\arduino-0022~~\arduino-0022\hardware/tools/avr/bin/avrdude -CC:\Users\~~Liz\Desktop~~\arduino-~~0022\arduino-<br/>~~ 0022\hardware/tools/avr/etc/avrdude.conf ~~-v -v -v -v -patmega168p -cstk500v1 -P\\.\COM4 -b19200 -e -Ulock:w:0x3F:m -Uefuse:w:0x00:m~~<br/> ~~-Uhfuse:w:0xdd:m -Ulfuse:w:0xff:m -F~~		C:\Users\....\arduino-0022\hardware/tools/avr/bin/avrdude -CC:\Users\...\arduino-0022\hardware/tools/avr/etc/avrdude.conf<br/>
			-v -v -v -v -patmega168p -cstk500v1 -P\\.\COM4 -b19200 -e -Ulock:w:0x3F:m -Uefuse:w:0x00:m-Uhfuse:w:0xdd:m -Ulfuse:w:0xff:m -F

			You have to complete this command with the exactly location of the folder arduino-0022.
	The bootloader have been burn!		The bootloader have been burn!

ElizabethPaz: /* Instructions */

2013-03-20T15:03:28Z

Instructions

← Older revision		Revision as of 15:03, 20 March 2013
Line 17:		Line 17:
	Open the ArduinoISP firmware (in Examples) to your Arduino board.		Open the ArduinoISP firmware (in Examples) to your Arduino board.

	* Select Tools > Board and Serial Port > Arduino Uno (the board that we are using as a programmer)		* Select '''Tools > Board''' and '''Tools > Serial Port > Arduino Uno''' (the board that we are using as a programmer)
	{\|		{\|
	\| [[File:Select-arduino-uno.png\|thumb\|upright=2\|alt=Connection]]		\| [[File:Select-arduino-uno.png\|thumb\|upright=2\|alt=Connection]]

ElizabethPaz: /* Instructions */

2013-03-20T15:02:30Z

Instructions

← Older revision		Revision as of 15:02, 20 March 2013
Line 43:		Line 43:
	* If this doesn't work, execute cmd.exe and execute the following command:		* If this doesn't work, execute cmd.exe and execute the following command:
	C:\Users\Liz\Desktop\arduino-0022\arduino-0022\hardware/tools/avr/bin/avrdude -CC:\Users\Liz\Desktop\arduino-0022\arduino-<br/> 0022\hardware/tools/avr/etc/avrdude.conf -v -v -v -v -patmega168p -cstk500v1 -P\\.\COM4 -b19200 -e -Ulock:w:0x3F:m -Uefuse:w:0x00:m<br/> -Uhfuse:w:0xdd:m -Ulfuse:w:0xff:m -F		C:\Users\Liz\Desktop\arduino-0022\arduino-0022\hardware/tools/avr/bin/avrdude -CC:\Users\Liz\Desktop\arduino-0022\arduino-<br/> 0022\hardware/tools/avr/etc/avrdude.conf -v -v -v -v -patmega168p -cstk500v1 -P\\.\COM4 -b19200 -e -Ulock:w:0x3F:m -Uefuse:w:0x00:m<br/> -Uhfuse:w:0xdd:m -Ulfuse:w:0xff:m -F

	<code>Code source</code>

	The bootloader have been burn!		The bootloader have been burn!

ElizabethPaz: /* Instructions */

2013-03-20T15:01:25Z

Instructions

← Older revision		Revision as of 15:01, 20 March 2013
Line 43:		Line 43:
	* If this doesn't work, execute cmd.exe and execute the following command:		* If this doesn't work, execute cmd.exe and execute the following command:
	C:\Users\Liz\Desktop\arduino-0022\arduino-0022\hardware/tools/avr/bin/avrdude -CC:\Users\Liz\Desktop\arduino-0022\arduino-<br/> 0022\hardware/tools/avr/etc/avrdude.conf -v -v -v -v -patmega168p -cstk500v1 -P\\.\COM4 -b19200 -e -Ulock:w:0x3F:m -Uefuse:w:0x00:m<br/> -Uhfuse:w:0xdd:m -Ulfuse:w:0xff:m -F		C:\Users\Liz\Desktop\arduino-0022\arduino-0022\hardware/tools/avr/bin/avrdude -CC:\Users\Liz\Desktop\arduino-0022\arduino-<br/> 0022\hardware/tools/avr/etc/avrdude.conf -v -v -v -v -patmega168p -cstk500v1 -P\\.\COM4 -b19200 -e -Ulock:w:0x3F:m -Uefuse:w:0x00:m<br/> -Uhfuse:w:0xdd:m -Ulfuse:w:0xff:m -F

			<code>Code source</code>

	The bootloader have been burn!		The bootloader have been burn!

ElizabethPaz: /* Instructions */

2013-03-20T14:40:11Z

Instructions

← Older revision		Revision as of 14:40, 20 March 2013
Line 42:		Line 42:

	* If this doesn't work, execute cmd.exe and execute the following command:		* If this doesn't work, execute cmd.exe and execute the following command:
	C:\Users\Liz\Desktop\arduino-0022\arduino-0022\hardware/tools/avr/bin/avrdude -CC:\Users\Liz\Desktop\arduino-0022\arduino- 0022\hardware/tools/avr/etc/avrdude.conf -v -v -v -v -patmega168p -cstk500v1 -P\\.\COM4 -b19200 -e -Ulock:w:0x3F:m -Uefuse:w:0x00:m -Uhfuse:w:0xdd:m -Ulfuse:w:0xff:m -F		C:\Users\Liz\Desktop\arduino-0022\arduino-0022\hardware/tools/avr/bin/avrdude -CC:\Users\Liz\Desktop\arduino-0022\arduino-<br/> 0022\hardware/tools/avr/etc/avrdude.conf -v -v -v -v -patmega168p -cstk500v1 -P\\.\COM4 -b19200 -e -Ulock:w:0x3F:m -Uefuse:w:0x00:m<br/> -Uhfuse:w:0xdd:m -Ulfuse:w:0xff:m -F

	The bootloader have been burn!		The bootloader have been burn!

ElizabethPaz: /* Instructions */

2013-03-20T14:39:24Z

Instructions

← Older revision		Revision as of 14:39, 20 March 2013
Line 11:		Line 11:
	= Instructions =		= Instructions =

	#First, Replace the files ''arduino-0022\hardware\arduino\boards.txt'' and ''arduino-0022\hardware\tools\avr\etc\avrdude.conf'' by this two files: [[File:Boards.txt]] and [[File:Avrdude.conf.txt]]		* First, Replace the files ''arduino-0022\hardware\arduino\boards.txt'' and ''arduino-0022\hardware\tools\avr\etc\avrdude.conf'' by this two files: [[File:Boards.txt]] and [[File:Avrdude.conf.txt]]
	Close the Arduino IDE.		Close the Arduino IDE.

	#Open the IDE. You will see three new boards:		* Open the IDE. You will see three new boards:
	Open the ArduinoISP firmware (in Examples) to your Arduino board.		Open the ArduinoISP firmware (in Examples) to your Arduino board.

	# Select Tools > Board and Serial Port > Arduino Uno (the board that we are using as a programmer)		* Select Tools > Board and Serial Port > Arduino Uno (the board that we are using as a programmer)
	{\|		{\|
	\| [[File:Select-arduino-uno.png\|thumb\|upright=2\|alt=Connection]]		\| [[File:Select-arduino-uno.png\|thumb\|upright=2\|alt=Connection]]
	\|}		\|}

	# Upload the ArduinoISP sketch into your programmer		* Upload the ArduinoISP sketch into your programmer
	{\|		{\|
	\| [[File:Arduino-isp.jpg\|thumb\|upright=2\|alt=Connection]]		\| [[File:Arduino-isp.jpg\|thumb\|upright=2\|alt=Connection]]
	\|}		\|}

	# Disconnect the USB cable from the Arduino Uno.
	# ~~Wire~~ the ~~Wild~~ ~~Thumper~~ ~~Controller with~~ the Arduino Uno ~~as shown in the picture~~		* Disconnect the USB cable from the Arduino Uno.

			* Wire the Wild Thumper Controller with the Arduino Uno as shown in the picture
	{\|		{\|
	\| [[File:Wildtrumper-board-isp-bootloader-burning.jpg\|thumb\|upright=1\|alt=Connection]]		\| [[File:Wildtrumper-board-isp-bootloader-burning.jpg\|thumb\|upright=1\|alt=Connection]]
	\| [[File:Schema_burn_bootloader.png\|thumb\|upright=3\|alt=Schema]]		\| [[File:Schema_burn_bootloader.png\|thumb\|upright=3\|alt=Schema]]
	\|}		\|}

	# Plug in your USB cable to the programmer (Arduino Uno). Select the item in the '''Tools > Board > DAGU product w/Atmega 168''', then the item '''Tools > Burn Bootloader > Arduino as ISP'''.		* Plug in your USB cable to the programmer (Arduino Uno). Select the item in the '''Tools > Board > DAGU product w/Atmega 168''', then the item '''Tools > Burn Bootloader > Arduino as ISP'''.
	{\|		{\|
	\| [[File:Select-arduino-nano.png\|thumb\|upright=2\|alt=Connection]]		\| [[File:Select-arduino-nano.png\|thumb\|upright=2\|alt=Connection]]
	\| [[File:Select-arduino-as-isp.png\|thumb\|upright=2\|alt=Schema]]		\| [[File:Select-arduino-as-isp.png\|thumb\|upright=2\|alt=Schema]]
	\|}		\|}

	# If this doesn't work, execute cmd.exe and execute the following command:		* If this doesn't work, execute cmd.exe and execute the following command:
	C:\Users\Liz\Desktop\arduino-0022\arduino-0022\hardware/tools/avr/bin/avrdude -CC:\Users\Liz\Desktop\arduino-0022\arduino- 0022\hardware/tools/avr/etc/avrdude.conf -v -v -v -v -patmega168p -cstk500v1 -P\\.\COM4 -b19200 -e -Ulock:w:0x3F:m -Uefuse:w:0x00:m -Uhfuse:w:0xdd:m -Ulfuse:w:0xff:m -F		C:\Users\Liz\Desktop\arduino-0022\arduino-0022\hardware/tools/avr/bin/avrdude -CC:\Users\Liz\Desktop\arduino-0022\arduino- 0022\hardware/tools/avr/etc/avrdude.conf -v -v -v -v -patmega168p -cstk500v1 -P\\.\COM4 -b19200 -e -Ulock:w:0x3F:m -Uefuse:w:0x00:m -Uhfuse:w:0xdd:m -Ulfuse:w:0xff:m -F
	The bootloader have been burn!		The bootloader have been burn!
⚫	# Close all Arduino IDE windows
⚫	# Open arduino-0022\arduino-0022\lib\preferences.txt and change: ''upload.using=bootloader'' by ''upload.using=arduinoisp''
⚫	# Open the Arduino IDE, open your sketch. Make sure '''Tools > Board is set~~'''~~ to the target chip.

		⚫	* Close all Arduino IDE windows
⚫	# Compile and upload the sketch

		⚫	* Open arduino-0022\arduino-0022\lib\preferences.txt and change: ''upload.using=bootloader'' by ''upload.using=arduinoisp''

		⚫	* Open the Arduino IDE, open your sketch. Make sure '''Tools > Board''' is set to the target chip.

		⚫	* Compile and upload the sketch

ElizabethPaz: /* Instructions */

2013-03-20T14:37:57Z

Instructions

← Older revision		Revision as of 14:37, 20 March 2013
Line 11:		Line 11:
	= Instructions =		= Instructions =

	# First, Replace the files ''arduino-0022\hardware\arduino\boards.txt'' and ''arduino-0022\hardware\tools\avr\etc\avrdude.conf'' by this two files: [[File:Boards.txt]] and [[File:Avrdude.conf.txt]]		#First, Replace the files ''arduino-0022\hardware\arduino\boards.txt'' and ''arduino-0022\hardware\tools\avr\etc\avrdude.conf'' by this two files: [[File:Boards.txt]] and [[File:Avrdude.conf.txt]]
	Close the Arduino IDE.		Close the Arduino IDE.
	# Open the IDE. You will see three new boards:		#Open the IDE. You will see three new boards:
	Open the ArduinoISP firmware (in Examples) to your Arduino board.		Open the ArduinoISP firmware (in Examples) to your Arduino board.
	# Select Tools > Board and Serial Port > Arduino Uno (the board that we are using as a programmer)		# Select Tools > Board and Serial Port > Arduino Uno (the board that we are using as a programmer)

ElizabethPaz: /* Instructions */

2013-03-20T14:37:02Z

Instructions

← Older revision		Revision as of 14:37, 20 March 2013
Line 13:		Line 13:
	# First, Replace the files ''arduino-0022\hardware\arduino\boards.txt'' and ''arduino-0022\hardware\tools\avr\etc\avrdude.conf'' by this two files: [[File:Boards.txt]] and [[File:Avrdude.conf.txt]]		# First, Replace the files ''arduino-0022\hardware\arduino\boards.txt'' and ''arduino-0022\hardware\tools\avr\etc\avrdude.conf'' by this two files: [[File:Boards.txt]] and [[File:Avrdude.conf.txt]]
	Close the Arduino IDE.		Close the Arduino IDE.

	# Open the IDE. You will see three new boards:		# Open the IDE. You will see three new boards:

	Open the ArduinoISP firmware (in Examples) to your Arduino board.		Open the ArduinoISP firmware (in Examples) to your Arduino board.

	# Select Tools > Board and Serial Port > Arduino Uno (the board that we are using as a programmer)		# Select Tools > Board and Serial Port > Arduino Uno (the board that we are using as a programmer)

	{\|		{\|
	\| [[File:Select-arduino-uno.png\|thumb\|upright=2\|alt=Connection]]		\| [[File:Select-arduino-uno.png\|thumb\|upright=2\|alt=Connection]]
	\|}		\|}

	# Upload the ArduinoISP sketch into your programmer		# Upload the ArduinoISP sketch into your programmer

	{\|		{\|
	\| [[File:Arduino-isp.jpg\|thumb\|upright=2\|alt=Connection]]		\| [[File:Arduino-isp.jpg\|thumb\|upright=2\|alt=Connection]]
	\|}		\|}

	# Disconnect the USB cable from the Arduino Uno.		# Disconnect the USB cable from the Arduino Uno.

	# Wire the Wild Thumper Controller with the Arduino Uno as shown in the picture		# Wire the Wild Thumper Controller with the Arduino Uno as shown in the picture

	{\|		{\|
	\| [[File:Wildtrumper-board-isp-bootloader-burning.jpg\|thumb\|upright=1\|alt=Connection]]		\| [[File:Wildtrumper-board-isp-bootloader-burning.jpg\|thumb\|upright=1\|alt=Connection]]
	\| [[File:Schema_burn_bootloader.png\|thumb\|upright=3\|alt=Schema]]		\| [[File:Schema_burn_bootloader.png\|thumb\|upright=3\|alt=Schema]]
	\|}		\|}

	# Plug in your USB cable to the programmer (Arduino Uno). Select the item in the '''Tools > Board > DAGU product w/Atmega 168''', then the item '''Tools > Burn Bootloader > Arduino as ISP'''.		# Plug in your USB cable to the programmer (Arduino Uno). Select the item in the '''Tools > Board > DAGU product w/Atmega 168''', then the item '''Tools > Burn Bootloader > Arduino as ISP'''.

	{\|		{\|
	\| [[File:Select-arduino-nano.png\|thumb\|upright=2\|alt=Connection]]		\| [[File:Select-arduino-nano.png\|thumb\|upright=2\|alt=Connection]]
	\| [[File:Select-arduino-as-isp.png\|thumb\|upright=2\|alt=Schema]]		\| [[File:Select-arduino-as-isp.png\|thumb\|upright=2\|alt=Schema]]
	\|}		\|}

	# If this doesn't work, execute cmd.exe and execute the following command:		# If this doesn't work, execute cmd.exe and execute the following command:

	C:\Users\Liz\Desktop\arduino-0022\arduino-0022\hardware/tools/avr/bin/avrdude -CC:\Users\Liz\Desktop\arduino-0022\arduino- 0022\hardware/tools/avr/etc/avrdude.conf -v -v -v -v -patmega168p -cstk500v1 -P\\.\COM4 -b19200 -e -Ulock:w:0x3F:m -Uefuse:w:0x00:m -Uhfuse:w:0xdd:m -Ulfuse:w:0xff:m -F		C:\Users\Liz\Desktop\arduino-0022\arduino-0022\hardware/tools/avr/bin/avrdude -CC:\Users\Liz\Desktop\arduino-0022\arduino- 0022\hardware/tools/avr/etc/avrdude.conf -v -v -v -v -patmega168p -cstk500v1 -P\\.\COM4 -b19200 -e -Ulock:w:0x3F:m -Uefuse:w:0x00:m -Uhfuse:w:0xdd:m -Ulfuse:w:0xff:m -F

	The bootloader have been burn!		The bootloader have been burn!

	# Close all Arduino IDE windows		# Close all Arduino IDE windows

	# Open arduino-0022\arduino-0022\lib\preferences.txt and change: ''upload.using=bootloader'' by ''upload.using=arduinoisp''		# Open arduino-0022\arduino-0022\lib\preferences.txt and change: ''upload.using=bootloader'' by ''upload.using=arduinoisp''

	# Open the Arduino IDE, open your sketch. Make sure '''Tools > Board is set''' to the target chip.		# Open the Arduino IDE, open your sketch. Make sure '''Tools > Board is set''' to the target chip.